■商品概要
【メーカー品番】280-721H

■詳細説明
HIGHSIDER AKRON-RS license plate holder

The HIGHSIDER AKRON-RS license plate holder adapts perfectly to thelines of your bike thanks to its design．

The model-specific bracket of the HIGHSIDER AKRON-RS allowsmounting on the original mounting points of your bike and thus areplacement without further drilling or cutting．
To prevent damage to cables， all sharp-edged feedthroughs areprotected by a rubber membrane grommet．

The license plate is made of sheet steel and 2 mm thick． Theprecise cutting is done by laser． After edging， theweather-resistant black powder coating is applied．
This ensures the optimal fit and durability．
Through the stepless adjustment you can bring the plate withoutdrilling in the desired position． To keep the plate in thisposition， there is an additional locking screw．

The turn signal brackets of the HIGHSIDER AKRON-RS are adjustablein width and therefore suitable for any type of accessory turnsignal． This adjustment option allows you to adapt the position foryour turn signals to the most varied number plates． To allowmounting the turn signals without disconnecting them from thewiring harness， the 10 mm holes are slotted to the side．

You can also adjust the position of the reflector individually viaa slider． An adaptation to the different designs of the EU licenseplates is therefore no problem．

To screw the license plate securely and reduce vibration， tworubber washers are included． Another rubber buffer supports thelicense plate on its underside．

Details:

- model-specific bracket
- infinitely adjustable turn signal holder
- slotted turn signal holder for easy mounting without cableseparation
- infinitely adjustable reflector， E-approved
- suitable for European number plates
- infinitely adjustable tilt angle
- additional screw for optimum position security
- easy fixing without further work steps (e． g．B． Drilling)
- easy mounting of the license plate through slotted holes

Included in the scope of delivery of the HIGHSIDER AKRON-RSare:

- Model-related bracket with mounting parts
- HIGHSIDER AKRON-RS license plate retaining plate
- Adjustable turn signal brackets
- E-tested reflector with adjustable bracket
- Mounting instructions

Notes:
- If there are side reflectors fitted to your original number plateholder， these must be refitted in a suitable position or replacedwith new ones．
- The special turn signal holder 280-974 is optionally availablefor the original turn signals．

Tip:
If you have not found a model-specific license plate holder foryour vehicle， the universal license plate holders from HIGHSIDER，which are available in many different designs， are certainly a goodalternative．

■注意点
※ナンバープレートサイズが日本の規格ではありませんので、取り付ける際にはステーによる加工などが必要なりますのでご注意下さい。
※輸入品のため、説明書が付属する場合、外国語の説明書となります。
※メーカー都合により商品の仕様変更がある場合がございます。ご了承ください。

　※画像はイメージです。
■適合車種
Z 1000 (ZR1000F)
 Z 1000 (ZR1000F) 年式: 14-16
Z 1000 ABS (ZR1000G)
 Z 1000 ABS (ZR1000G) 年式: 14-16
Z 1000 ABS (ZR1000H)
 Z 1000 ABS (ZR1000H) 年式: 17-18
Z 1000 ABS R EDITION (ZR1000J)
 Z 1000 ABS R EDITION (ZR1000J) 年式: 17-18
Z 1000 ABS SPECIAL EDITION (ZR1000G)
 Z 1000 ABS SPECIAL EDITION (ZR1000G) 年式: 14
Z 1000 SPECIAL EDITION (ZR1000F)
 Z 1000 SPECIAL EDITION (ZR1000F) 年式: 14